Garmin’s endurance advantage has long been one of the defining features of its watches. While many smartwatches struggle to last more than a few days, some Garmin models can run for weeks, or in certain low-power modes, even indefinitely with enough sunlight.

A detailed new engineering analysis by efpasia breaks down how Garmin achieved this advantage, tracing the hardware decisions and solar innovations that power watches like the Fenix 8, Enduro 3, and Instinct 3 Solar.
“Most smartwatches last a day or two between charges, but with Garmin some models display an infinity symbol where the battery percentage should be.”
What makes that possible is not one single trick. It is a stack of engineering decisions that all reinforce one another: the glass, the solar layer beneath it, the MIP display, the processors, and the firmware’s power management.
The first big secret behind Garmin’s endurance advantage is how the company redesigned solar charging itself.
Solar Charging: From Fenix 6 to Today
Garmin’s solar watch story begins with the Fenix 6 Solar, the first Garmin watch to integrate solar charging directly into the lens stack. That early design used technology acquired from SunPartner Technologies, a French company Garmin purchased as it neared bankruptcy.
The first-generation approach worked, but it came with tradeoffs. A semitransparent solar layer sat between the display and the outer lens, using a dual-density layout: highly efficient cells around the display edge and a much less efficient array across the main screen. The idea was simple: capture most energy where it wouldn’t interfere with readability while allowing light through the center so the display could still be seen clearly.
“The solar layer beneath the screen gave the display a subtle reddish tint… a visible sign Garmin was still polishing a brand-new technology.”
Over the next several years, Garmin expanded solar charging across more of its lineup, including the Instinct Solar, Instinct 2 Solar, the Enduro line, and even Edge cycling computers. But under the hood, the solar architecture remained largely unchanged throughout this period. The real hardware jump came with the Fenix 8 Solar and Enduro 3.
Those watches moved the solar hardware entirely off the main display area and into a dense ring around the bezel. That eliminated the reddish tint while allowing Garmin to pack more photovoltaic material where it could capture energy most efficiently. Paired with a Power Sapphire lens, Garmin claims the redesign delivers up to five times the solar charging power of the previous generation.
That same second-generation solar hardware later came to the Instinct 3 Solar, pushing the rugged lineup into “unlimited” territory in select battery modes under sufficient sun exposure.
Where the Instinct 2 Solar managed roughly 48 hours of GPS tracking with solar, the Instinct 3 Solar pushed that to around 130 hours—with independent reviewers confirming burn rates under one percent per hour even in high-drain GPS modes.
The “Solar Sandwich” Inside the Watch
Every solar Garmin is essentially built as a layered stack:
Cover lens → solar layer → display → motherboard
The solar charging component is not an accessory or external panel. It is integrated directly into the watch face assembly. Garmin currently uses two solar lens variants.
Power Glass uses strengthened glass with the solar cells bonded beneath it. This configuration appears on mid-tier devices such as the Instinct series.
Power Sapphire replaces that outer glass with synthetic sapphire crystal—the second hardest transparent material after diamond, rating 9 on the Mohs scale. This version is used on premium devices such as the Fenix 8 Solar, Enduro 3, and tactix models.
In the original Gen 1 design, the solar material stretched across both the bezel and the main display. In the Gen 2 architecture, Garmin relocated the photovoltaic cells entirely to the bezel area. This design both improves efficiency and removes any visual interference with the screen.
Why Solar Actually Works on Garmin Watches
On paper, solar charging on a watch sounds minor. The power involved is measured in milliwatts.
“Solar isn’t pumping tons of power into your watch—think tiny amounts measured in milliwatts.”
But Garmin watches are engineered to consume extremely little power.
“Low power use plus a steady solar top-up means you can actually break even – or even come out ahead.”
That is the key. MIP displays consume almost no energy while showing a static image. Garmin’s firmware aggressively manages processor clock speeds and sensor activity to minimize power consumption.
Garmin’s solar arrays are also managed by a Power Management Unit running Maximum Power Point Tracking (MPPT) algorithms—the same technique used in large rooftop solar installations. These controllers constantly adjust electrical parameters to extract the maximum energy from the cells as light conditions change.
Geometry is another challenge. Solar panels perform best when sunlight strikes them at a 90-degree angle. But a wrist-mounted device rarely faces the sun directly. As the wearer moves, the watch constantly shifts orientation. Garmin compensates by arranging many small photovoltaic cells at slightly different angles so the watch can capture energy across a wide range of positions.
Under favorable conditions, early solar models could restore roughly 20 percent of battery capacity over a day of sunlight. The second-generation solar architecture significantly improves that figure.
The Processor Story Matters Too
Battery life is not just about solar panels—it is also about what sits beneath the display. Earlier devices like the Fenix 6X Pro ran on an NXP Cortex-M4 platform capable of bursts up to 150 MHz. Garmin reused this processor across several product generations, prioritizing efficiency over raw performance.
Newer models like the Fenix 8 use the NXP i.MX RT500 platform built around a Cortex-M33 core with an integrated DSP. This newer architecture provides improved power efficiency, hardware security features, and support for newer capabilities such as audio processing.

One particularly interesting change is that Garmin eliminated external RAM entirely. Older models used a separate memory chip primarily to buffer map data. In the Fenix 8 generation, Garmin moved that workload onto the processor’s internal SRAM. This reduces power consumption and simplifies the motherboard, though it can make map rendering slightly slower.
The GNSS system also saw a major upgrade. The Fenix 6 generation relied on a Sony single-band GPS chip. The Fenix 8 uses a modern multi-band GNSS chipset that can track multiple constellations simultaneously for improved accuracy.
Shared Silicon Across Garmin’s Lineup
One surprising discovery from teardowns is how similar Garmin watches can be internally.
A teardown of the Forerunner 245 Music revealed that its core processor architecture was essentially the same as the Fenix series of the same generation. Differences came down primarily to sensors, storage capacity, NFC support, and software-enabled features.
This shared hardware platform means efficiency improvements developed for flagship devices often propagate throughout the lineup. When Garmin improves power management for a Fenix device, many of those gains also benefit watches like the Forerunner series.
MIP vs AMOLED: The Biggest Battery Tradeoff
If there is one design decision at the center of Garmin’s battery advantage, it is the continued use of MIP displays on endurance-focused models.
MIP displays reflect ambient light and consume almost no energy when showing static content. In direct sunlight they actually become easier to read. AMOLED screens look far better indoors—offering vivid colors, deep blacks, and smooth animations—but every pixel consumes power continuously. Looking at the same generation illustrates the difference:
The Instinct 3 AMOLED offers up to 24 days of smartwatch battery life. The Instinct 3 Solar with MIP can achieve effectively unlimited runtime in some modes when exposed to sufficient sunlight.
“On an AMOLED watch, the solar panel would be feeding a furnace with a candle.”
That helps explain why Garmin has not yet introduced a mainstream solar AMOLED watch.
The Competitive Landscape
Six years after Garmin launched its first solar watch, the competitive response remains surprisingly thin.
Apple sits at the opposite end of the design philosophy. Devices like the Apple Watch emphasize connectivity, apps, and smartphone integration rather than ultra-long battery life.
Coros has built a strong reputation for efficient endurance watches and even introduced a solar cycling computer with the DURA, but the company still has not released a solar watch.
Suunto briefly experimented with solar on the first-generation Vertical but removed the feature in the next generation when switching to AMOLED displays.
The analysis argues that Garmin’s advantage is not just solar glass—it is the entire stack: Power Sapphire lenses, low-power MIP displays, MPPT power management, efficient processors, and aggressive firmware optimization. Replicating any one of these elements is possible; replicating the entire system is a multi-year engineering effort.
Looking Ahead
One interesting paradox emerges from the analysis: as watches become more efficient, solar energy becomes more important, not less.
When a device consumed 50 milliwatts, a few milliwatts of solar input barely mattered. But as modern wearables drop closer to 5 milliwatts, the same solar input can dramatically extend runtime.
Garmin also appears to be making pragmatic decisions about where solar technology makes sense as the industry shifts toward AMOLED displays. The company has removed MIP options from newer Forerunner and Fenix models in favor of AMOLED, and even introduced an AMOLED variant of the Instinct 3, a device known for its monochrome MIP display. At the same time, Garmin has quietly removed solar charging from newer Edge cycling computers, whose large transmissive LCD displays consume far more power.
For the full technical breakdown—including teardown photos and component-level analysis—see efpasia’s original article.






Join the conversation. A free account lets you comment, reply and say how updates are running.
Sign up freeSign in
I personally hope for an early release of Enduro 4, where the MIP display will play a major role.
I could imagine that MIP will only be available for the Enduro and maybe for the Tactix. Fenix in the future will be AMOLED only. I owned every Enduro and currently have the E3 and I really love it even though I enjoy my Tactix Pro AMOLED screen too.